I’ve had my Polymer 80 P940Cv1 frame quit for quite awhile – a couple years in fact. I’ve had it so long I forgot where I got some of the parts. Anyway, some friends have been wanting to go shooting yesterday and I had some spare time. Last week I bought a cordless Dremel so I could finally finish this thing. This won’t be a complete review of the P940Cv1, just my initial impressions. After I have a chance to shoot it more and gather my notes I’ll do a complete review and shooting report.
The instructions suck…
The P940Cv1 doesn’t come with instructions, which is kind of weird considering it’s not obvious how it goes together. Polymer80 has instructions in PDF format on their web site, but these instructions are much better IMO. Polymer80 recommends using a slide vise and drill press for the milling operations on the frame. My drill press wasn’t deep enough to fit the slide vise, so I tried holding the block by hand. BIG mistake – the bit grabbed the frame and marred it pretty good before I got it away from the bit. My bad…
Looking for solutions, I found a video from Marine Gun Builder that shows how to finish a Polymer80 frame without a drill press. I couldn’t afford the fancy fret snips he recommends so I got the closest snips I could find at Home Depot. They worked OK, but my frame didn’t turn out nearly as pretty as Marine Gun Builder’s. No worries – I’d already marred it anyway. The important thing was – would it shoot? More on that later…
Other parts you’ll need
The Polymer80 kits only come with the parts needed for the frame itself. Besides the frame kit, you’ll need a Frame Parts Kit (not sold by Polymer80) and a complete slide assembly. The Polymer 80 frames need Glock Gen 3 compatible parts. If you use Gen 4 or later parts you might damage the frame and will definitely void your warranty. Polymer80 specifically mentions that Lone Wolf Distributors uses some Gen 4 parts in their kits, in spite of labeling them as “Gen 3 compatible.” Simple – don’t use a Lone Wolf Distributor kit in your P80 frame kit. I prefer OEM Glock parts that I get from Glockmeister. For my slide, I bought a no-name Gen 3 compatible G19 slide assembly on eBay.
One thing to watch for is to make sure you put the right parts in the right hole. The 2 pins that come with the frame kit are for the front and back holes in the frame. The middle (small) hole is for the locking block pin that will come with your Frame Parts Kit. You’ll need to install this pin before installing the slide release assembly but after putting the trigger assembly in place. This part was a little confusing to me so I had to call Polymer80 for guidance. I can let you know they DO answer the phone and were able to help me. GREAT customer service.
Problems? What problems?
The only problem I had putting together the P940Cv1 kit was the slide block spring. For some reason I can’t get it to seat correctly. It’s in the front groove far enough to not fall out, but barely. This might be due to the fact that I started way back when with a Lone Wolf Distributors kit, and the spring might have come from them – which could mean it’s a Gen 4 part (for some reason, Glock changed this spring from Gen 3 to Gen 4). I have known Gen 3 springs on the way from Glockmeister, so we’ll see. The one I put in held well enough for test firing.
Other than that, no problems that weren’t self induced. The pins were really tight, but that might actually be a good thing. For those familiar with Glocks, this won’t come apart easily with the Glock tool. Hammer and punch will definitely be needed. Once I got it put together, it function checked fine so off to the range…
But does it shoot?
I didn’t have any Gen 3 G19 magazines, so I borrowed one from my Gen 4. Fit was fine. I had some reservations about shooting it because of the slide lock spring issue, but life is short so… I loaded 2 rounds into the mag and inserted. Seated fine, so far so good. Time to pull the trigger. Took aim, pulled the trigger, and… it went bang just like it’s supposed to. Second round fed OK, pulled the trigger again, went bang again, and the slide locked back on the empty magazine just like it’s supposed to.
Inserted a full magazine. Bang… bang… and ftf. Drop magazine, clear round, insert magazine, rack slide, and… ftf. Lather, rinse, repeat and… another ftf. On the 3rd try I used the slide release instead of racking the slide and the round fed. (I SWEAR I wasn’t “riding the slide”…) I shot the remaining rounds in the magazine with no issues. Shot through two more full mags with no issues and called it a day. A successful day.
I didn’t do any formal accuracy testing, but it seemed as accurate as my Glock 22 that I brought for comparison. So far, I’m happy. In fact, happy enough that I ordered a P940Cv1 second frame kit, along with their subcompact (P940SC). Hopefully the next one will turn out as nice as the ones Marine Gun Builder turns out. Until next time…
Peace out,
porcupine